> Solving Problems > An Error Code is Displayed on the LCD Screen

An Error Code is Displayed on the LCD Screen

A code is displayed on the LCD screen if there is an error or information that requires your attention. If a code is displayed, follow the solutions below to solve the problem.

Code

Situation

Solutions

E-01

A printer error has occurred.

Open the inner cover and the scanner unit, and then remove any paper or protective material inside the printer. Turn the power off and on again.

E-02

A scanner error has occurred.

Turn the power off and on again.

E-11

An ink pad needs to be replaced.

Contact Epson or an authorised Epson service provider to replace the ink pad*1. It is not a user-serviceable part.

However, non-printing features such as scanning are available.

E-12

A borderless printing ink pad needs to be replaced.

Contact Epson or an authorised Epson service provider to replace the borderless printing ink pad*2. It is not a user-serviceable part.

Borderless printing is not available, but printing with a border is available.

W-01

A paper jam has occurred.

Remove the paper from the printer and press the button displayed on the bottom of the LCD screen to clear the error. In some cases, you need to turn the power off and on again.

W-11

An ink pad is nearing the end of its service life.

Contact Epson or an authorised Epson service provider to replace the ink pad*1. It is not a user-serviceable part. The message will be displayed until the ink pad is replaced.

Press the button to resume printing.

W-14

A borderless printing ink pad is nearing the end of its service life.

Contact Epson or an authorised Epson service provider to replace the borderless printing ink pad*2. It is not a user-serviceable part. The message will be displayed until the ink pad is replaced.

Press the button to resume printing.

I-22

Set Wi-Fi from the Push Button (WPS).

Push the access point button. If there is no button on the access point, open the access point setting window, and then click the button displayed in the software.

I-23

Set Wi-Fi from the PIN Code (WPS).

Enter the PIN code displayed on the LCD screen into the access point or computer within two minutes.

I-31

Set Wi-Fi from the Wi-Fi Auto Connect.

Install the software on your computer, and then press the OK button when Wi-Fi setup starts.

I-41

Paper Setup Auto Display is disabled. Some functions cannot be used.

If Paper Setup Auto Display is disabled, you cannot use AirPrint. To use AirPrint, enable Paper Setup Auto Display.

I-60

Your computer may not support WSD (Web Services for Devices).

The scan to computer (WSD) feature is only available for computers running English versions of Windows 10, Windows 8.1, Windows 8, Windows 7 or Windows Vista. Make sure that the printer is correctly connected to the computer.

Recovery Mode

The printer has started in recovery mode because the firmware update failed.

Follow the steps below to try to update the firmware again.

1. Connect the computer and the printer with a USB cable. (During recovery mode, you cannot update the firmware over a network connection.)

2. Visit your local Epson website for further instructions.

*1In some print cycles a very small amount of surplus ink may be collected in the ink pad. To prevent ink leakage from the pad, the printer is designed to stop printing when the pad has reached its limit. Whether and how often this is required will vary according to the number of pages you print, the type of material that you print and the number of cleaning cycles that the printer performs. The need for replacement of the pad does not mean that your printer has ceased to operate in accordance with its specifications. The printer will advise you when the pad requires replacing and this can only be performed by an authorised Epson Service provider. The Epson warranty does not cover the cost of this replacement.

*2In some print cycles a very small amount of surplus ink may be collected in the borderless printing ink pad. To prevent ink leakage from the pad, the product is designed to stop borderless printing when the pad has reached its limit. Whether and how often this is required will vary according to the number of pages you print using the borderless print option. The need for replacement of the pad does not mean that your printer has ceased to operate in accordance with its specifications. The printer will advise you when the pad requires replacing and this can only be performed by an authorised Epson Service provider. The Epson warranty does not cover the cost of this replacement.