Error Code is Displayed on the Status Menu

001

The product was turned off by a power failure.

-

106

Cannot print from the computer due to the access control settings.

Contact your printer administrator.

107

User authentication failed. The job has been canceled.

• Make sure that the user name and password are correct.

• Select Settings > General Settings > System Administration > Security Settings > Access Control. Enable the user restriction function, and then allow the job without an authentication information.

108

Confidential job data was deleted when the printer was turned off.

-

109

The received fax was already deleted.

-

110

The job was printed on one side only because the paper loaded does not support double sided printing.

If you want to perform 2-sided printing, load paper that supports 2-sided printing.

201

The memory is full.

• Print received faxes from Job Status in Job/Status .

• Delete received faxes saved in the inbox from Job Status in Job/Status.

• If you are sending a monochrome fax to a single destination, you can send it by using Direct Send.

• Divide your originals in two or more to send them in several batches.

202

The line was disconnected by the recipient machine.

Wait for a while and then try again.

203

The product cannot detect the dial tone.

• Make sure that the phone cable is connected correctly and the phone line is working.

• When the printer is connected to the PBX or the terminal adapter, change the Line Type setting to PBX.

• Select Settings > General Settings > Fax Settings > Basic Settings > Dial Tone Detection, and then disable the dial tone setting.

204

The recipient machine is busy.

• Wait for a while and then try again.

• Check the recipient's fax number.

205

The recipient machine does not answer.

Wait for a while and then try again.

206

The phone cable is incorrectly connected to the LINE and EXT. port of the product.

Check the connection of the LINE port and the EXT. port of the printer.

207

The product is not connected to the phone line.

Connect the phone cable to the phone line.

208

The fax could not be sent to some of the specified recipients.

Print a Fax Log or Last Transmission report for previous faxes from Fax Report in the Fax mode to check the failed destination. When the Save Failure Data setting is enabled, you can resend a fax from Job Status in Job/Status.

301

There is not enough storage space available to save the data in the memory device.

• Increase the storage space in the memory device.

• Reduce the number of documents.

• Lower the scanning resolution or increase the compression ratio to reduce the size of the scanned image.

302

The memory device is write-protected.

Disable write protection on the memory device.

303

No folder has been created to save the scanned image.

Insert another memory device.

304

The memory device has been removed.

Reinsert the memory device.

305

An error occurred while saving the data to the memory device.

If the external device is accessed from a computer, wait for a while and then try again.

306

The memory is full.

Wait until other ongoing jobs are finished.

311

A DNS error has occurred.

• Select Settings > General Settings > Network Settings > Advanced > TCP/IP, and then check the DNS settings.

• Check the DNS settings for the server, the computer, or the access point.

312

An authentication error has occurred.

Select Settings > General Settings > Network Settings > Advanced > Email Server > Server Settings, and then check the server settings.

313

A communication error has occurred.

• Print a network connection report to check if the printer is connected to the network.

• Select Settings > General Settings > Network Settings > Advanced > Email Server > Server Settings to check the email server settings. You can check the cause of the error by running connection check.

• The authentication method of the settings and the email server may not match. When you select Off as the authentication method, make sure the authentication method of the email server is set to None.

314

The data size exceeds the maximum size for attached files.

• Increase the Attached File Max Size setting in the scan settings.

• Lower the scanning resolution or increase the compression ratio to reduce the size of the scanned image.

315

The memory is full.

Retry after other ongoing jobs are finished.

321

A DNS error has occurred.

• Select Settings > General Settings > Network Settings > Advanced > TCP/IP, and then check the DNS settings.

• Check the DNS settings for the server, the computer, or the access point.

322

An authentication error has occurred.

Check the Location settings.

323

A communication error has occurred.

• Check the Location settings.

• Print a network connection report to check if the printer is connected to the network.

324

A file with the same name already exists in the specified folder.

• Delete the file with the same name.

• Change the file name prefix in File Settings.

325

326

There is not enough storage space available in the specified folder.

• Increase the storage space in the specified folder.

• Reduce the number of documents.

• Lower the scanning resolution or increase the compression ratio to reduce the size of the scanned image.

327

The memory is full.

Wait until other ongoing jobs are finished.

328

The destination was wrong or the destination does not exist.

Check the Location settings.

331

A communication error occurred while acquiring the destination list.

Print a network connection report to check if the printer is connected to the network.

332

There is not enough storage space available to save the scanned image in the destination storage.

Reduce the number of documents.

333

The destination could not be found because the destination information was uploaded to the server before sending the scanned image.

Select the destination again.

334

An error occurred while sending the scanned image.

-

341

A communication error has occurred.

• Check the connections for the printer and the computer. If you are connecting over a network, print a network connection report to check if the printer is connected to the network.

• Make sure that Epson Event Manager is installed on the computer.

401

There is not enough storage space available to save the data in the memory device.

Increase the storage space in the memory device.

402

The memory device is write-protected.

Disable write protection on the memory device.

404

The memory device has been removed.

Reinsert the memory device.

405

An error occurred while saving the data to the memory device.

• Reinsert the memory device.

• Use a different memory device on which you have created a folder using the Create a folder to save fax data function.

411

A DNS error has occurred.

• Select Settings > General Settings > Network Settings > Advanced > TCP/IP, and then check the DNS settings.

• Check the DNS settings for the server, the computer, or the access point.

412

An authentication error has occurred.

Select Settings > General Settings > Network Settings > Advanced > Email Server > Server Settings, and then check the server settings.

413

A communication error has occurred.

• Select Settings > General Settings > Network Settings > Advanced > Email Server > Server Settings to check the email server settings. You can check the cause of the error by running connection check.

• The authentication method of the settings and the email server may not match. When you select Off as the authentication method, make sure the authentication method of the email server is set to None.

• Print a network connection report to check if the printer is connected to the network.

421

A DNS error has occurred.

• Select Settings > General Settings > Network Settings > Advanced > TCP/IP, and then check the DNS settings.

• Check the DNS settings for the server, the computer, or the access point.

422

An authentication error has occurred.

Select Settings > General Settings > Fax Settings > Receive Settings > Save/Forward Settings, and then check the settings of the folder selected in Save/Forward Destination.

423

A communication error has occurred.

• Print a network connection report to check if the printer is connected to the network.

• Select Settings > General Settings > Fax Settings > Receive Settings > Save/Forward Settings, and then check the settings of the folder selected in Save/Forward Destination.

425

There is not enough storage space available in the forwarding destination folder.

Increase the storage space in the forwarding destination folder.

428

The destination was wrong or the destination does not exist.

Select Settings > General Settings > Fax Settings > Receive Settings > Save/Forward Settings, and then check the settings of the folder selected in Save/Forward Destination.