1. TOP»
  2. ESC/POS® Command Reference for TM Printers »
  3. Commands Arranged by Function »
  4. Customize Commands »
  5. User setup »
  6. GS ( E   <Function 11>

Select your printer model

Parameters are refined by the selected printer.
  • EU-m30
  • TM-J2000
  • TM-J2100
  • TM-L90
  • TM-L90 LFC
  • TM-L100
  • TM-m10
  • TM-m30
  • TM-m30II
  • TM-m30II-H
  • TM-m30III
  • TM-m30III-H
  • TM-m30II-NT
  • TM-m30II-S
  • TM-m30II-SL
  • TM-m50
  • TM-m50II
  • TM-m50II-H
  • TM-P20
  • TM-P20II
  • TM-P60
  • TM-P60II
  • TM-P80
  • TM-P80II
  • TM-T20
  • TM-T20II
  • TM-T20III
  • TM-T20IIIL
  • TM-T20IV-L
  • TM-T20X
  • TM-T20X-II
  • TM-T70
  • TM-T70II
  • TM-T81III
  • TM-T82II
  • TM-T82III
  • TM-T82IIIL
  • TM-T82IV-L
  • TM-T82X
  • TM-T82X-II
  • TM-T83III
  • TM-T83IV
  • TM-T88IV
  • TM-T88V
  • TM-T88VI
  • TM-T88VII
  • TM-T90
  • TM-T100
  • TM-U220
  • TM-U220II
  • TM-U230

GS ( E   <Function 11>

[Name]

Set the configuration item for the serial interface

[Format]

ASCII
   
GS
  
(
  
E
  
pL
  
pH
  
fn
  
a
  
d1 ... dk
Hex
1D
28
45
pL
pH
0B
a
d1 ... dk
Decimal
29
40
69
pL
pH
11
a
d1 ... dk

[Range]

(pL + pH × 256) = 3 – 65535
fn = 11
d = 48 – 57 [a = 1]
d = 48 – 50 [a = 2]
d = 48, 49 [a = 3]
d = 55, 56 [a = 4]
k = 1 – 6
a: different depending on the printers

[Default]

different depending on the printers

[Description]

Sets the configuration item for the serial interface specified by a.
a
Configuration item
1
Transmission speed
2
Parity
3
Flow control
4
Data length
  • Transmission speed (a = 1) is specified by number. The baud rate that can be specified differs, depending on the printer model.
  • Example:
  • When defining 19200 bps: 5 bytes as "19200" (Hex = 31h, 39h, 32h, 30h, 30h / Decimal = 49, 57, 50, 48, 48)
  • Parity (a = 2) is specified by d as follows:
  • d
    Function
    48
    Select no parity
    49
    Select odd parity
    50
    Select even parity
  • Flow control (a = 3) is specified by d as follows:
  • d
    Function
    48
    Select Flow control of DTR/DSR
    49
    Select Flow control of XON/XOFF
  • Data length (a = 4) is specified by d as follows:
  • d
    Function
    55
    Select 7 bits length
    56
    Select 8 bits length

[Notes]

  • This function works in user setting mode.
  • This function works with serial interface printers.
  • The communication condition set by this function is enabled by executing Function 2 or restarting the printer. It is necessary to change the communication condition of the host to be the same as the printer to communicate with the printer.
  • To enable the communication condition set by this function, select "by memory switch" in the DIP switch settings (Interface condition selection).
  • Communication conditions set are valid until the following operations are executed. They are not initialized by power off or ESC @.
    • Execution of this function.
    • Execution of memory switch setting mode by panel operation when the power is turned on (supported by some printer models.)
 

Quick Access

  • [Name]
  • [Format]
  • [Range]
  • [Description]
  • [Notes]
ESC/POS® includes patented or patent pending commands. The contents must not be disclosed to third parties.


ESC/POS® Command Reference for TM Printers

  1. TOP»
  2. ESC/POS® Command Reference for TM Printers »
  3. Commands Arranged by Function »
  4. Customize Commands »
  5. User setup »
  6. GS ( E   <Function 11>

Jump to the top